Custom isolation, regulation and efficiency
A poorly specified power transformer becomes voltage instability and heat that only shows up after installation
A power transformer within its rated range can still fail where it matters: unstable regulation under variable load, heat above the design value, or insulation that falls short for the installation environment. The right question is not which catalog model to buy. It is which specification your application demands.
- São José dos Pinhais · PR · Brazil
- Dry-type per ABNT NBR5356-11
- Custom manufacturing in Brazil
What a power transformer solves in your project
A power transformer delivers the voltage and current the rest of the circuit needs, galvanically isolating the supply side from the load side. That isolation is not a construction detail: it is the safety layer that protects equipment and operator against a fault on the power side.
The unit can be step-up, when it raises the voltage applied to the primary, or step-down, when it lowers the voltage to the desired level. This is what sustains the entire electric power system: in generation and transmission, step-down transformers reduce voltages such as 69 kV and 138 kV to standardized metering and protection levels; in distribution, they step down again to the 127 V, 220 V or 380 V that reach the consumer. Under Brazil's NR-10, the threshold between high and low voltage in alternating current is 1000 V.
The question that reaches our engineering team is rarely which transformer to buy. It is which specification solves the project's real problem: unstable voltage regulation under variable load, heat above what was planned, or insulation that falls short for the installation environment.

Galvanic isolation and efficiency: what protects the system
Galvanic isolation between primary and secondary protects the load circuit against a fault on the supply side. It is a safety requirement, not an optional feature. Combined with electrostatic and electromagnetic shielding, this isolation also reduces the interference the transformer introduces into the rest of the system, which matters especially in equipment sensitive to electrical noise.
The Toroid power transformer line operates at up to 98% efficiency and up to 1% regulation, with an insulation voltage of up to 4 kV and a frequency range of 50 Hz to 800 Hz. That covers both standard grid applications and equipment that runs at non-standard frequencies.
Critical operations need more than power. They need stability.
Toroid do Brasil
Autotransformer or isolation transformer: what changes at low voltage
At low voltage, two constructions solve different problems and are often confused at quoting time. The autotransformer has only the core and a single winding, and is used to correct the supply level, for example turning 127 Vac into 220 Vac or the other way around. It is the economical choice when the goal is only to match the voltage.
The isolation transformer has separate primary and secondary windings. Besides matching the voltage, it keeps galvanic isolation between the two sides, which turns the transformer into complementary protection for the downstream equipment. When the project needs a fault on the supply not to cross over to the load, that separation is what decides between the two constructions.

Electrostatic shielding and magnetic shielding: two distinct protections
The specifications table declares galvanic isolation with electrostatic and electromagnetic shielding. These are two different things, and the choice between them depends on which problem the project needs to solve.
- Electrostatic shielding. Applied between the primary and the secondary, it reinforces the galvanic isolation between the windings and gets a dedicated lead for grounding the transformer. It protects mainly against lightning surges that arrive through the supply.
- Magnetic shielding. Layers of silicon steel sheet applied around the transformer to reduce the magnetic field it emits. It keeps the transformer itself from interfering with the other components in the circuit.
One protects the transformer from what comes from outside, the other protects what surrounds the transformer. In equipment sensitive to electrical noise it is common to need both, which is why shielding appears as its own item in the specification checklist.

Never short the secondary of a power transformer
Here the rule is the opposite of the one for the current transformer, and confusing the two is costly. A power transformer is not designed to operate with its secondary shorted. Connecting the secondary windings together raises the circuit current far above design, which damages the transformer and creates a risk of fire, explosion and electric shock for anyone handling the equipment.
In the current transformer the opposite applies: there the secondary can never be left open. Each family has its own forbidden condition, and the one that applies to one does not apply to the other.
Raw materials: silicon steel and enameled copper
The core starts from grain-oriented silicon steel, in M3 (0.23 mm) and M4 (0.27 mm) thicknesses, cut in widths from 10 mm to 80 mm according to the project specification. It is this high-permeability magnetic lamination that sustains the performance declared in the specifications table.
The winding uses G2 enameled copper, in gauges from 5 AWG to 36 AWG, to handle everything from low instrumentation currents to more demanding loads, without changing supplier between one range of the line and another.

Potted, resin-cast or plain: which finish protects the project
The finish changes what the transformer withstands in the installation environment, not the technology itself. Mylar provides electrical insulation in standard applications. Epoxy resin encapsulation adds mechanical protection and resistance to moisture, dust and temperature swings, which increases durability in harsh environments.
Specifying the finish for the real installation environment avoids a common problem: a transformer that works well on the test bench and degrades earlier than planned in the field.

Power transformer for medical equipment
Medical equipment has electrical safety requirements that leave no room for interpretation: robust galvanic isolation, low leakage current and predictable behavior under fault. The dry-type construction, with no insulating oil, covered by ABNT NBR5356-11, fits this application profile. RoHS compliance is relevant for anyone manufacturing for a regulated market.
Here, documented technical specification weighs more than unit price. Medical equipment approval does not tolerate a supplier that cannot back its technical data with a standard.

Power transformer for solar energy and distributed generation
In distributed generation and solar energy, transformer efficiency accumulates over thousands of operating hours. One extra percentage point of loss is energy generated and not delivered. Efficiency of up to 98%, combined with regulation of up to 1%, contributes directly to overall system performance, especially in installations where space is already constrained by the project definition.

Before the quote
How to specify a power transformer
This set of information is what separates a catalog quote from a custom specification, including when the standard does not fit the final product's enclosure and the project requires customization.
- Rated input and output voltage (V)
- Rated power (VA) or load current on the secondary (A)
- Rated frequency (Hz): standard grid or the equipment's specific frequency
- Insulation class
- Minimum and maximum dimensions available in the enclosure or final product (mm)
- Application type and installation environment: standard, industrial, outdoor or medical
- Need for electrostatic or magnetic shielding
- Finish type
- Order volume and project deadline
Power transformer line specifications
| Power range | 5 VA to 15 kVA |
|---|---|
| Operating frequency | 50 Hz to 800 Hz |
| Isolation | galvanic, with electrostatic and electromagnetic shielding |
| Insulation voltage | up to 4 kV |
| Efficiency | up to 98% |
| Regulation | up to 1% |
| Available finishes | Mylar or epoxy resin |
| Reference standard (dry-type) | ABNT NBR5356-11 |
Standard line parameters. Applications outside these ranges are evaluated case by case by engineering.
Questions that come up with this specification
What is the efficiency of a Toroid power transformer?
The Toroid line operates at up to 98% efficiency and up to 1% regulation.
At what voltage is a circuit considered high voltage?
Under Brazil's NR-10, any alternating-current voltage above 1000 V is considered high voltage, and values below that are low voltage. Generation and transmission work at high voltage, and it is in distribution that the step down to the low-voltage levels that feed the end equipment takes place.
What is the difference between an autotransformer and an isolation transformer?
An autotransformer has only the core and a single winding, and is used to correct the supply level, for example from 127 Vac to 220 Vac. An isolation transformer has separate primary and secondary windings, so besides matching the voltage it keeps galvanic isolation between the two sides, which works as complementary protection for the equipment.
What is electrostatic shielding in a transformer?
It is a layer applied between the primary and the secondary that reinforces the galvanic isolation between the windings, with a dedicated lead for grounding the transformer. It serves mainly as protection against lightning surges that arrive through the supply.
What happens if the secondary of a power transformer is shorted?
Unlike a current transformer, a power transformer is not designed to operate with its secondary shorted. Connecting the secondary windings together raises the circuit current, damages the transformer and creates a risk of fire, explosion and electric shock for anyone handling the equipment.
Can a power transformer be used in medical equipment?
Yes. The dry-type construction, with no insulating oil, falls under ABNT NBR5356-11, and the Toroid line is RoHS compliant.
What is the difference between a Mylar finish and epoxy resin?
Mylar provides electrical insulation in standard applications. Epoxy resin encapsulation adds mechanical protection and resistance to moisture, dust and temperature swings, and is recommended for harsh environments.
Can the power transformer have a toroidal core?
Yes. The line can be supplied with a toroidal core or in conventional E/I construction, depending on the project's constraints. Each technology serves different needs.
Technical quote
Send the specification, or just the panel's constraint. Our team replies with the sizing.
Voltage, current, available space and applicable standard. If any data point is still missing, our team helps you pin it down.

